BAKFlip MX4 (Gen 3) Hard Folding Tonneau Cover
We designed the BAKFlip MX4 (Gen 3) hard folding tonneau cover to deliver premium truck bed protection without sacrificing functionality. Our aluminum panel construction resists dents and corrosion while maintaining a sleek matte finish that complements any truck style.
This three-panel folding system opens completely for full bed access, flips forward to rest behind the cab, or secures in multiple positions for hauling taller cargo. Our Gen 3 upgrade includes enhanced UV-resistant coating and reinforced hinge systems that handle daily use in extreme weather conditions.
- Aircraft-grade aluminum panels with matte finish resist dents and UV fade
- Three-panel fold design opens to full bed access or secures partially open
- Gen 3 reinforced hinge system rated for 300+ pounds distributed evenly
- Automatic slam latch system engages with OEM tailgate lock
- Low-profile design sits flush with bed rails for aerodynamic efficiency
Aluminum Construction & Surface Finish
We build every MX4 panel from aircraft-grade aluminum that resists rust, corrosion, and impact damage better than vinyl or soft covers. The powder-coated matte finish withstands intense UV exposure without fading or cracking, maintaining its appearance through years of sun and weather.
Our Gen 3 coating process adds an extra protective layer that repels water and prevents oxidation even in coastal or high-humidity environments. The aluminum maintains structural integrity in temperatures from -40°F to 140°F, so you never worry about warping or brittleness.
Three-Panel Folding System & Bed Access
The three-panel design folds completely open to rest behind the cab, giving you unobstructed access to your entire truck bed for loading oversized cargo or equipment. Each panel locks into position independently, so you can open just the section you need while keeping the rest of your bed secure.
Our reinforced aluminum hinges handle up to 300 pounds of distributed weight when the cover is fully closed and latched. You can stand on the cover to reach roof racks or tie-downs without worrying about damaging the panels or hinge mechanisms.
Installation Process & Compatibility
Our clamp-on rail system installs in approximately 30 minutes using basic hand tools and the included hex keys. No drilling required means you preserve your truck’s factory warranty and can remove the cover completely if needed.
The MX4 fits most 5.5-foot, 6.5-foot, and 8-foot truck beds from major manufacturers including Ford, Chevrolet, GMC, Ram, Toyota, and Nissan. We manufacture bed-specific models for each truck configuration, so side rails mount flush with your bed walls and tailgate seals align perfectly. The system works with most spray-in bed liners and over-rail accessories like ladder racks or crossbars.
Explore Other Premium Aluminum Tonneau Covers
What people are saying
Common Questions About the BAKFlip MX4 (Gen 3)
Yes, the MX4 works with most spray-in bed liners and drop-in liners from major manufacturers. We include foam spacers that adjust the rail height to accommodate liner thickness and ensure a flush fit.
The side rails clamp over your bed walls, so liner material won't interfere with installation. For best results, install the cover on a clean, dry bed and use the spacers to fine-tune panel alignment with your specific liner configuration.
Our Gen 3 aluminum panels and reinforced hinge system support up to 300 pounds evenly distributed across the closed cover. You can safely stand on the cover to access roof racks or tie-downs without damaging the panels.
Avoid placing concentrated weight on a single point or hinge area. The 300-pound rating applies when weight distributes across multiple panels with all slam latches engaged and locked.
Absolutely. Each of the three panels locks independently in multiple positions, so you can open just the rear section or middle section while keeping the rest of your bed covered and secure.
This partial-open feature lets you haul items like toolboxes or equipment that sit higher than the bed rails while protecting the front portion of your bed. The panels lock firmly in place and won't shift during highway driving.
No drilling required. Our clamp-on rail system mounts to your bed walls using adjustable clamps and the included hex keys. Installation takes approximately 30 minutes and preserves your factory warranty.
You can remove the cover completely at any time without leaving holes or permanent modifications. The clamp system holds securely through all weather conditions and highway speeds.
The Gen 3 upgrade includes enhanced UV-resistant coating that prevents fading and oxidation better than previous versions, plus reinforced hinge mechanisms with improved corrosion resistance. We also upgraded the weather seals to maintain flexibility in extreme cold.
Both generations use the same aircraft-grade aluminum panel construction and three-fold design. Gen 3 represents refinements in coating technology and hinge durability based on years of customer feedback from harsh-weather environments.
Yes, the MX4 sits flush with your bed rails and doesn't interfere with factory tie-downs, cleats, or bed dividers. The low-profile design leaves full access to all bed mounting points when the cover is open or closed.
You can also install most over-rail accessories like crossbars or ladder racks. Our customer service team can verify compatibility with specific rack systems if you need confirmation before ordering.
Our automatic slam latches engage with your truck's factory tailgate lock mechanism. When you close the rear panel and lock your tailgate, both the cover and bed access secure simultaneously with one key.
This integrated security means you don't need separate keys or additional locks. The system works with all OEM tailgate locks and most aftermarket locking tailgate handles.